AutoScan Кабеля, разъемы»
Адаптеры диагностики автомобиля» Сканеры, Считыватели кодов» Адаптеры Диагностики и Настройки ГБО автомобиля»
AutoScan
Поддержка
В Избранное Добавить в избранное
ABS/ AIR BAG »
По маркам»
Грузовики»
Автобусы»
ЧИСТКА ФОРСУНОК» Поддержка

CantieCar v3.x bluetooth новое поколение Аппаратно-программного комплекса AllinOne с поддержкой кан шины.

CANtieCAR v3.x (Bluetooth ready)

Информация - для иллюстрации о поддерживаемых режимах в CantieCar v3.x bluetooth


Режим ELM поддерживаемый в CantieCar v3.x bluetooth
ELM323 - OBD (ISO) to RS232 Interpreter (v2.0)
The ELM323 completes our trio of single function OBDII ICs. It supports the ISO 9141-2 and ISO 14230-4 standards that are used by many vehicles throughout the world.
The ELM323 transparently converts between a 10.4KHz ISO data stream and standard ASCII characters, allowing trouble codes and operating parameters to be easily retrieved without the need for special software. No knowledge of data formatting, error checking, bus initiation etc. is needed either, as the ELM323 handles all of it for you.
The present version of the ELM323 (v2.0) provides several programmable features that the previous versions did not offer. It allows programmable header bytes, adjustable timeouts, the ability to report in the packed data mode, and offers a special monitoring mode as well. This is in addition to all of the capabilities that the v1.x ICs offered - the full seven byte command structure, two line (K and L) initiation, software selectable linefeeds and character echoing, and the visual feedback provided by the four LED outputs.
If you currently use one of our v1.x ICs, you will be pleased to know that this version (v2.0) is pin-compatible with the old, so you can simply replace your present IC with one of these, and immediately begin enjoying these new features.
Подробнее >>

Режим P.A.Soft BMW Scanner поддерживаемый в CantieCar v3.x bluetooth
- P.A.Soft BMW Scanner v1.2.5
- P.A.Soft BMW Scanner v1.3.6
- P.A.Soft BMW Scanner v1.4.0 Demo
- P.A.Soft BMW Scanner v1.4.x
BMW Scanner (version 1.4.0)
for chassis E38 E39 E46 E53 E83 E85
BMW Scanner V1.4.0 intended to work with BMW 3, 5, 7 series, X3, X5 SUV and Z4 roadster cars.
Short functions list:
Determination of chassis, model, engine, gearbox and complete set
Searching of all units and reading:
- identification data
- odometer value
- VIN and ADFG
- programming info (UIF)
- errors (DTC)
Reading and saving in files:
- program memory
- EEPROM
- coding data
- amount of DTCs and DTCs shadow-memory
- live data
- programming info (User Info Fields)
Copying ZCS (IKE - EWS) and FA (IKE - LCM) coding
... and other functions in various units

"Unlocked" functions to show possibilities of full version:
DTCs description in DME MS43.0, EWS3, SRS MRS4
Clearing DTCs in same units
EWS-DME synchronization code in DME MS43.0
Live data in DME MS43.0, EWS3, SRS MRS2 and MRS4
Status of all keys in EWS3
EWS3 coding data interpretation
Equipment correction in SRS MRS4
Some screenshots of BMW Scanner V1.4.0

Режим Lawicel поддерживаемый в CantieCar v3.x bluetooth
- Lawicel CAN232 v3 (6:High, 14:Low)
- Lawicel CANUSB v1 (6:High, 14:Low)
CAN tools by LAWICEL AB
Welcome to the new combined CAN232 and CANUSB website. Since much information is common for both our products, we decided to put them into one new website. It is still under construction, but you can find the old sites here for CAN232 and here for CANUSB until we are all done.

CANUSB is a very small and inexpensive dongle that plugs into any PC USB Port and gives an instant CAN connectivity. This means it can be treated by software as a standard COM Port (serial RS232 port) which eliminates the need for any extra drivers or by installing adirect driver DLL for faster communications and higher CAN bus loads. ending and receiving can be done in standard ASCII format or using the windowsthreaded CANUSB DLL.

CAN232 is a very small blue dongle that plugs into any PC COM Port, or any other RS232 port in an embedded system and gives an instant CAN connectivity. This means it can be treated by software as a standard COM Port (serial RS232 port) which eliminates the need for any extra drivers. Sending and receiving can be done in standard ASCII format.


Режим PonyProg2000 поддерживаемый в CantieCar v3.x bluetooth
- PonyProg2000
If you are looking for a simple but powerful programmer you are right, it's here.
PonyProg is a serial device programmer software with a user friendly GUI framework available for Windows95/98/ME/NT/2000/XP and Intel Linux. Its purpose is reading and writing every serial device. At the moment it supports I?C Bus, Microwire, SPI eeprom, the Atmel AVR and Microchip PIC micro.
SI-Prog is the programmer hardware interface for PonyProg.
With PonyProg and SI-Prog you can program Wafercard for SAT, eeprom within GSM, TV or CAR-RADIO. Furthermore it can be used as a low cost starter kit for PIC and AVR.
Support PonyProg Support This Project
PonyProg works also with other simple hardware interfaces like AVR ISP (STK200/300), JDM/Ludipipo, EasyI2C and DT-006 AVR (by Dontronics).
Features
Support 24C01, 24C02, 24C04, 24C08, 24C16 I?C Bus EEPROM
Support 24C32, 24C64, 24C65, 24C128, 24C256, 24C512 I?C Bus EEPROM
Auto detect 24XX EEPROM capacity
Support 24C325 and 24C645 I?C Bus EEPROM
Support Siemens SDE2516, SDE2526, SDA2546, SDA2586, SDA3546, SDA3586 EEPROM (as 24XX Auto)
Support AT17C65, AT17C128, AT17C256, AT17C512, AT17C010 I?C Bus EEPROM
Support Siemens SDE2506 EEPROM
Detect the bank roll over capability of some old 24XX EEPROM
Support AT90S1200, AT90S2313, AT90S2323, AT90S2343, AT90S4414, AT90S4434, AT90S8515, AT90S8535 Flash micro
Support AT90S2323, AT90S2343, AT90S2333, AT90S4433, AT90S4434, AT90S8535, AT90S8534
Auto detect AVR microcontroller type
Support the AVR microcontroller ATmega103, ATmega161, ATmega163, ATmega 323, ATmega128, ATmega8, ATmega16, ATmega64, ATmega32, ATmega162, ATmega169, ATmega8515, ATmega8535
Support the AVR ATmega44, 88, 168, 164, 324, 644, 640,1280, 1281, 2560, 2561 (untested)
Support the AVR AT90can32, 64, and 128 (untested)
Support the AVR ATtiny12, ATtiny15, ATtiny26, ATtiny2313
Support the AVR ATtiny13, 25, 45, 85, 261, 461, and 861 (untested)
Read ATtiny12 and ATtiny15 Oscillator Calibration Byte
Write lock bits to protect the AVR micro from reading
Write both the Flash and EEPROM memory of the AVR micro at once
Support the AT89S8252 and AT89S53 micro
Support 93C06, 93C46, 93C56, 93C57, 93C66, 93C76, 93C86 Microwire EEPROM (C and LC series, the CS serie is not supported yet)
Support 93C13 (as a 93C06) and 93C14 (as a 93C46) Microwire EEPROM
Access microwire eeproms in either 8 and 16 bit organization
Improved support PIC 16C84/16F84 micro
Support PIC 16F873/874/876/877 and PIC 16F84A micro
Support PIC 16F873A/874A/876A/877A and PIC 16F627/628 micro (untested)
Support PIC 12C508/509 micro
Support PIC 12C671/672 micro (untested)
Support 25010, 25020, 25040 SPI EEPROM
Support 25080, 25160, 25320, 25640, 25128, 25256 Big SPI EEPROM
Support 25642 and 95640 Big SPI EEPROM
Support NVM3060 eeprom
Support MDA2061/MDA2062 eeprom
Support X2444/X2445 eeprom
Support S24H30 (untested)
Read/Write Intel hex format file as well as raw binary file
Read/Write Motorola S-record format file
Read/Write CSM format file
Features a custom E?P format file to store the EEPROM characteristics, an editable comment and memory content all together with CRC
Enhanced buffer edit, text and hexadecimal
Work with Windows95/98/ME and WindowsNT/2000/XP and Linux*
Reload file button
Fill buffer command
Security bits editing for AVR, AT89S and PIC
Serial number programming
Script files for batch programming
Improved speed with WinNT/2000/XP with a driver for direct I/O.
*Not all interfaces are supported in every operating system, for more informations look at the documentation.
Screen dump

Режим EDiTH Eberspacher ISO поддерживаемый в CantieCar v3.x bluetooth
- EDiTH Eberspacher ISO Adapter
Диагностика Отопительных систем.

Режим OpenPort поддерживаемый в CantieCar v3.x bluetooth
What is OpenECU?
OpenECU is a project to enable open access to vehicle ECU's for tuning and logging purposes.
What does the "open" part mean?
Currently, most vehicles use a specialised computer to manage engine operations. These computers are programmed by the manufacturer and are "closed" except for the manufacturer themselves and liscenced service centers. This means the owner can't see how these devices are programmed to operate. "Open" means that the code used to program these ECU devices is available to be evaluated by everyone, including the owner.
What vehicles are currently supported?
Subaru vehicles from 2001 and some Mitsubishi vehicles.
What hardware do I need?
Windows 2000/XP Laptop with USB port for openport cable, or serial port for Accessport cable.
Logging: Cobb Accessport or Openport cable
Flashing:
non-dbw subaru:Openport 1.0-1.2 cable
dbw subaru: Openport 1.2 or 1.3M cable
Mitsubishi: Openport 1.3M cable
What Software do I need?
EcuFlash 1.44
(EcuFlash is a general-purpose ECU reflashing and editing tool that supports an ever-growing list of vehicles. EcuFlash uses the OpenPort vehicle interface to reflash vehicles via the OBDII port. EcuFlash also allows you to edit ECU data (known as 'maps' or 'tables') in a human-readable format using a XML-based definition system to translate the data. With properly setup definitions, the ROM from any vehicle can be edited. Future plans for EcuFlash include logging support / overlay, and live tuning.)
(EcuFlash 1.44.3721 for Windows XP/Vista/7/8)
EcuFlash version 1.38 for Mac OSX is provided for legacy OpenPort 1.3 cable support only. There is currently no EcuFlash support for the OpenPort 2.0 pending necessary OSX driver development. Alternately, EcuFlash 1.44 will work by running parallels on OSX.
(EcuFlash 1.38 for OSX 10.4+)

Режим MultiECUScan поддерживаемый в CantieCar v3.x bluetooth
MultiECUScan
Multiecuscan works fine on Windows 8, but you have to install .NET Framework 3.5 (which is not installed by default). You simply have to go to Control Panel -> Add remove programs -> Add remove windows components, and install .NET Framework 3.5. For the CANtieCAR interface you can install the same drivers as Windows 7. multiecuscan is a vehicle diagnostic software with advanced functions. It allows you to perform various diagnostics tasks on the supported vehicles/modules. In order to use the software you need an interface. The following interfaces are currently supported by the software: KL (also known as VagCom 409), ELM327 (1.3 or newer), OBDKey 1.40, OBDLink, ELM Scan 5, CANtieCAR. Bluetooth OBDKey, ELM 327 and OBDLink interfaces are fully supported but not recommended for special functions (like PROXI Alignment, remote control programming, IMA coding, etc.)! CANtieCAR is a professional multi-protocol interface with multiplexing capabilities. Just some informtion about multiecuscan programm from Official Web site multiecuscan:
Multiecuscan 1.7 FREE This is the limited version of the software. The program is free for personal use with some limitations (see table below and Supported Vehicles List). Multiecuscan 1.7 REGISTERED This is the full version of the software. It supports a large number of modules in Fiat, Alfa and Lancia vehicles. In order to use this version you need to buy a license. The license is valid for a SINGLE computer only! You will also need an interface (please check which interfaces are compatible with your car in Supported Vehicles List). You may also need an adapter cable in order to access certain modules in your car (you can check if you need an adapter in the Supported Vehicles List). Multiecuscan 1.7 MULTIPLEXED This is a special bundle of the software which includes a specialized professional interface. The included interface has multiplexing capabilities, it has support for all vehicles/modules and does not need additional adapters (except the 3-pin adapter for the old vehicles). The license of the software in this bundle is locked to the interface and you may install it on any number of computers but you can use it only with the included interface. FESmobile 2.1 This is diagnostics software for mobile devices. It runs on Windows Mobile and Windows CE devices (including Windows GPS devices). In order to use FESmobile you need to have a license. The license is free for everyone who has a license for multiecuscan. In most Windows CE devices you cannot install a CAB, so you have to download the RAR file and unppack it in a folder on your device, then run FESmobile.exe

Supported functions


Function FREE REGISTERED MULTIPLEXED FESmobile
KL (VagCom 409) interface Yes Yes No No
ELM 327 v1.3 (or later) interface Yes Yes No Yes, Bluetooth only
OBDKey 1.40 interface Yes Yes No Yes, Bluetooth only
OBDLink interface Yes Yes No Yes, Bluetooth only
CANtieCAR professional multi-protocol interface with multiplexing capabilities No No Yes Yes
Pin switching manual - with adapters or interface mod manual - with adapters or interface mod auto auto (CANtieCAR), manual (other interfaces)
License type N/A single computer,
many interfaces
many computers,
single interface
single device,
many interfaces
Read ECU identification Yes Yes Yes Yes
Clear fault codes Yes, for the FREE modules Yes Yes Yes
Read diagnostic data Yes, for the FREE modules Yes Yes Yes
Max number of parameters that can be selected simultaneously 4 Unlimited Unlimited Unlimited
Actuator tests Yes, for the FREE modules Yes Yes Yes
Parameter monitoring while executing an actuator test No Yes Yes No
Reset/Programming functions No Yes Yes Yes (limited set of functions)
CAN modules diagnostics (See Supported Vehicles section for a list of these modules) No Yes Yes Yes
Display data in graph Yes, 1 graph Yes, up to 4 graphs Yes, up to 4 graphs Yes
Max number of parameters on a graph 4 10 10 N/A
Multiple graph files No Yes Yes No
Insert tags in recorded data No Yes Yes No
Export data to CSV file Yes Yes Yes No
Auto-export data to CSV files No Yes Yes No
Import CSV data files No Yes Yes No
Multilanguage UI Yes Yes Yes Yes
Multilanguage data (parameter names, errors, etc.).
Supported languages: English, Deutsch, Italiano, Francais, Polski, Cesky, Magyar, Русский, Espanol, Nederlands, Turkce, Danish, Croatian, Portuguese(BR), Български
No Yes Yes Yes
Detailed description for Parameters, Errors, etc. in English Yes Yes Yes No
Parameter templates (a pre-selected group of parameters that can be selected with a single keypress) No Yes Yes No
Test run on any ECU ("simulation" mode) without interface Yes Yes Yes Yes
Auto-saved logs for each diagnostic session No Yes Yes Yes Time limit for a session Yes, 20 minutes No limit No limit No limit

Currentntly supported control modules:

See Supported Vehicles section for a complete list of supported modules on each make/model

Engine Management
- Bosch EDC15
- Bosch EDC15C7
- Bosch EDC16/CF3 Multijet
- Bosch EDC16/CF4 Multijet
- Bosch EDC16/CF5 Multijet
- Bosch EDC17CP52 CF5 Multijet
- Marelli 6JF Multijet
- Marelli 6F3 Multijet
- Marelli 8DF/CF5 Multijet
- Marelli 8F3 CF5 Multijet
- Visteon CF4 Diesel
- Bosch MSA 11
- Lucas DPNC TD100
- Lucas EPIC DCU3F
- Bosch Monomotronic MA1.7.3
- Bosch Monomotronic MA1.7
- Bosch Motronic ML4.1
- Bosch Motronic M1.7
- Bosch Motronic M3.7.1
- Bosch Motronic M2.10.3
- Bosch Motronic M2.10.4
- Bosch Motronic M1.5.5
- Bosch Motronic ME2.1
- Bosch Motronic ME3.1
- Bosch Motronic ME7.3.1
- Bosch Motronic ME7.3H4
- Bosch Motronic ME7.3H4M
- Bosch Motronic MED7.11
- Bosch Motronic Me7.6.3/CF4
- Bosch Motronic Me7.9.10/CF5
- Bosch Motronic MeD7.6.1/CF4
- Bosch Motronic MeD17.3.1 CF5
- Hitachi MPI
- Magneti Marelli IAW 1AF
- Magneti Marelli IAW 1AB
- Magneti Marelli IAW 5NF
- Magneti Marelli IAW 4AF/4EF/59F/5AF
- Magneti Marelli IAW 4GF BI/BLU-Power
- Magneti Marelli IAW 49F
- Magneti Marelli IAW 4SF
- Magneti Marelli IAW 5SF CF4
- Magneti Marelli IAW 4AF/4EF GAS
- Magneti Marelli IAW 5AF GAS
- Magneti Marelli IAW 5SF3/CF4
- Magneti Marelli IAW 5SF8/CF5
- Magneti Marelli IAW 5SF9/CF5
- Magneti Marelli IAW 7GF
- Magneti Marelli IAW 8GSF CF5
- Magneti Marelli IAW 8GMF CF5
- Delphi MT25E Injection
- Delphi MT27E Injection
- Landi Renzo LC02 LPG
- Metatron 6A0/EOBD CNG
- Metatron 6A0 CNG
- Metatron 5D0/EOBD CNG

Gearbox Management
- Marelli SELESPEED (old Alfa 156 SELESPEED)
- Marelli SELESPEED CFC208F
- Marelli SELESPEED CFC209F
- Marelli SELESPEED CFC218F
- Marelli SELESPEED CFC228F
- Marelli SELESPEED CFC300
- Marelli SELESPEED CFC328
- Marelli SELESPEED CFC348
- Marelli SELESPEED/DDCT CFC8TDF
- AISIN TIP-System
- AISIN AF40-6
- AISIN YLII 5
- AISIN YLII 5
- ZF 4HP20
- ZF 4HP18K

ABS
- Bosch ABS 5.7 VDC/ASR/TC
- Bosch ABS 8 VDC/ASR/ESP
- Bosch ABS 9 /ESP
- Lucas EBC 430 ABS
- Bosch ABS Teves MK20/MK70
- Bosch ABS 5.3 TC/ASR
- TRW Lucas ABS/ESP

Electric Power Steering
- TRW Electric Power Steering
- Delphi Electric Power Steering
- SAGEM Power Steering

Airbags
- ALLIED SIGNAL Airbags
- ALLIED MY97 Airbags
- BREED Airbags
- BREED MY97 Airbags
- TRW MY97 Airbags
- AUTOLIV MY99 Airbags
- SIEMENS MY99 Airbags
- TRW MY99 Airbags
- TRW MY03 Airbags
- TRW MY05 Airbags
- AUTOLIV MY06 Airbags
- SIEMENS MY06 Airbags
- AUTOLIV MY07 Airbags
- CONTINENTAL Airbags
- TRW Airbags

Body/Dashboard/Misc.
- Service Interval Reset
- CAN Setup / PROXI Alignment Procedure
- Remote control programming
- Delphi/Marelli Body Computer
- Marelli MF Body Computer
- Marelli Body Computer
- Delphi Body Computer
- Siemens Body Computer
- Visteon Instrument Panel
- Marelli Instrument Panel
- Nippon Instrument Panel
- Siemens Instrument Panel
- Siemens VDO Instrument Panel
- Mannesman VDO Instrument Panel
- Valeo parking control
- Bosch parking control
- BITRON Driver door, Passenger door and Boot
- G.E. PROCOND Driver door, Passenger door and Boot
- TRW Driver door and Boot
- Bosch XENON headlights
- Valeo XENON headlights
- Litronic XENON headlights
- Delphi Climate Control
- Harrison Climate Control
- Tyre Pressure Control (TPMS) TRW

Requirements:


Multiecuscan

- A computer that runs Windows XP, Windows Vista, Windows 7 (32/64), Windows 8 (you need to install .NET Framework 3.5)
- Microsoft .NET Framework Version 2.0 SP1 (or a newer version).
- K-line/VagCom 409, ELM 327 v1.3+, OBDLink, ELMScan, OBDKey 1.40 or CANtieCAR interface
- 1.5GHz CPU and better recommended

FESmobile

- A Windows Mobile (versions 5, 6.0, 6.1, 6.5) or Windows CE device with Bluetooth support. Could be a cell phone, PDA or GPS device.
- Bluetooth ELM 327 v1.3+, OBDLink, ELMScan, OBDKey 1.40 or CANtieCAR interface



Rambler's Top100 Submitter.ru